YESWELDER Welding Magnets Review

← All Posts shop equipment Weld Gear Team Last updated on July 19, 2026

There’s a specific frustration that happens when you’re tacking a frame and the magnet lets go just as you’re pulling the gun away. The piece shifts two degrees, you don’t catch it until three beads later, and now you’re grinding. YESWELDER’s arrow-shaped welding magnets have built a large following partly because they’re inexpensive enough to buy a set of four and partly because - when used within their actual holding limits - they don’t do that.

Welding magnets are passive magnetic fixtures used to hold ferrous metal pieces at fixed angles during tacking and light welding. The arrow shape is the industry standard for this price class: two magnetic faces meet at a point, giving you a defined 45, 90, or 135-degree contact angle without any adjustment mechanism.

The YESWELDER 25 lb set is the baseline option in their lineup and the one most buyers are looking for. Four pieces, 25 lb holding power per magnet, arrow shape, three working angles. Here’s what you need to know before ordering.

What the 25 lb Rating Actually Means

The 25 lb figure is the listed magnetic holding force. That’s a pull-off force measured against a flat steel plate at full surface contact - not a shear force, and not the force the magnet exerts when you’re holding a pipe at an angle with partial contact. In real shop use, expect effective holding on clean flat stock to be close to spec. On round pipe, rougher surfaces, or steel with mill scale, the working force drops because the contact area decreases.

For tacking small weldments, picture frames, and light bracket work, 25 lb is plenty. For holding heavy-wall structural plate in position, you want the 50 lb or 75 lb variants - or multiple 25 lb magnets positioned across the joint.

The 4-Piece Set: What You Get

The B08FHS8H38 set includes four arrow-shaped magnets at the 25 lb rating. The arrow design locks your workpiece at 45, 90, or 135 degrees depending on which face pair you use. That covers the angles you need for most fabrication work - butt joints, T-joints, corner joints, and mitered cuts.

The magnets are ferrite-core, not rare earth. Ferrite is weaker pound-for-pound than neodymium but significantly more heat-tolerant, which matters when you’re tacking close to the magnet body. Neodymium magnets used in some high-end fixturing tools can lose magnetism if repeatedly exposed to welding heat above 175°F.

YESWELDER also sells mixed sets: the B08FHS4DMN includes both 25 lb and 50 lb pieces (4 total), and the B0B9M68WXB goes up to 75 lb across a 6-piece set. If you know from the start you’ll be working with heavier stock, the mixed set makes more sense than buying the 25 lb set and upgrading later.

How YESWELDER Compares to TOOLIOM

TOOLIOM sells a nearly identical arrow magnet set (reviewed separately) at the same 25 lb and 50 lb ratings. The physical format - arrow shape, three working angles, ferrite core - is the same between the two brands. The differences come down to small details: handle cutout geometry, the feel of the molded grip areas, and minor differences in how cleanly the magnets contact round pipe.

In practice, both perform similarly on flat stock at their rated force. TOOLIOM offers a hexagon-format option that adds more angle versatility; YESWELDER’s standard product line is arrow-only at this tier. If you’re choosing strictly between the two arrow sets, the YESWELDER has a larger customer review base on Amazon, which gives you more real-world feedback on failure modes.

For an on/off magnetic switch with more precision and greater holding force, the Strong Hand Tools MSA46-HD (reviewed separately) is a step up in both capability and investment.

Named Flaw

The 25 lb magnets pick up grinding swarf and metal dust aggressively. After a grinding session near these magnets, you’ll spend time cleaning metal particles off all four pieces before they’ll seat cleanly against your workpiece. The ferrite core also attracts fine steel particles into the body’s seam areas. YESWELDER doesn’t build in an easy-clean switch - that’s the trade-off for the lower price point. If cleaning magnets is a workflow interruption you don’t want, look at the switchable magnet category instead.

Verdict

For a first set of welding magnets at home shop scale, the YESWELDER 25 lb 4-piece set is a solid starting point. It does the job at tack angles, the holding force is consistent on clean flat steel, and the four-piece quantity means you can fixture a small frame all at once without repositioning. Step up to the mixed 25/50 lb set if you work with anything heavier than 3/16” material regularly.

Buy YESWELDER 25 lb Welding Magnets 4-Piece Set on Amazon

FAQ

Are YESWELDER welding magnets strong enough for most jobs? For tacking light to medium steel at standard angles, yes. The 25 lb set handles flat stock and tubing in the 1/8” to 3/16” range comfortably. For heavier plate or structural work, move to the 50 lb or 75 lb variants in the YESWELDER lineup or use multiple magnets on the joint.

How many pieces come in a YESWELDER welding magnet set? The standard B08FHS8H38 listing is a 4-piece set of 25 lb magnets. YESWELDER also sells a 4-piece mixed set (25 lb and 50 lb) and a 6-piece set going up to 75 lb.

How does YESWELDER compare to TOOLIOM welding magnets? Both use arrow-shaped ferrite magnets at the same 25 lb and 50 lb ratings. Performance on flat stock is comparable. TOOLIOM offers a hexagon format with more angle options; YESWELDER has a larger Amazon review base. Neither has an on/off switch - for that feature, look at Strong Hand Tools or Magswitch products.

Can you weld directly over YESWELDER magnets? No, and you shouldn’t with any ferrite magnet. Use the magnets to tack-weld, then remove them before completing the weld. Prolonged heat exposure above roughly 175°F can demagnetize ferrite magnets over time.

What angles do YESWELDER welding magnets hold? The arrow design holds at 45, 90, and 135 degrees depending on which pair of faces you use against the workpiece.

Do YESWELDER magnets work on stainless steel? Only on ferritic or martensitic stainless steel grades, which are magnetic. Austenitic stainless (304, 316) is non-magnetic and won’t hold to any permanent magnet.

References

URL slug: yeswelder-welding-magnets Excerpt: YESWELDER’s 25 lb arrow-shaped welding magnets are a popular first set for home shops and light fabrication work. This review covers real holding force, the set contents, a direct comparison with TOOLIOM, and the one cleaning flaw that comes with every ferrite magnet at this price.